2024 Vermeer® Trommel Screens TR626EM

Information

2024 Vermeer® Trommel Screens TR626EM

Like the TR626 trommel screen, the TR626EM trommel screen takes the Vermeer trommel screen lineup to the next level with similar design and the ability to tackle tough jobs. The Vermeer TR626EM is equipped with a 150-hp (112-kW) Siemens motor which can help reduce jobsite noise and overall machine maintenance.

Features may include:

High production

The tensioned screens around the drum add rigidity, allowing use of small gauge wire, which helps increase production capacity and enable processing of wetter material.

Motor starter panel

The motor starter panel provides a variable frequency drive (VFD) panel.

Electric motors

Powered by two industrial-duty, fully enclosed and fan-cooled electric motors. A single 150-hp (112-kW) motor powers the hydraulic pump stack while a .75-hp (.6-kW) motor powers the cooling fan for the hydraulic system.

Ease of maintenance

The TR626EM was built with the operator in mind, designed with various access points to critical areas helping to make maintenance efficient.

Advance controls

Operators can control the machine through either the Vermeer DP10 display mounted on the control panel, or through a handheld transceiver remote.

Radial stacking conveyor

The stacking conveyor with a 180-degree arc increases the amount of material being stacked on the ground. Adjustable stacking height aids with dust control and helps avoid material being blown away.

Photos

Highlights

  • Jasper, Georgia
  • 2024
  • Vermeer®
  • Trommel Screens TR626EM
  • Available
  • Operation: 113 in | Apron Opening: 43 in | Drum Support Description: 4 in (10.2 cm) | Head/Tail Pulley Type: 38 in (99.65 cm) | Head Pulley Type: 38 in (99.65 cm) | Self-Cleaning Tail Pulley: 38 in (96.5 cm)
  • Operation: 15.9 ft | Apron Opening: 34 in | Hopper: 9.5 ft (2.9 m) from ground level at operating incline | Conveyor Belt Stacking: 16.6 ft (5.1 m) with drum at 4 deg

Specifications

  • 2024
  • Vermeer®
  • Trommel Screens
  • TR626EM
  • General
  • Siemens
  • 150 hp, 1800 rpm, 460 V, 3 phase
  • Drum: 48.8 cu in (800 cu cm) displacement | Conveyor: 38.4 cu-in
  • Leaf spring
  • 235-75R 17.5H qty. 4
  • System Voltage: 460 V
  • Apron Conveyor: 0-35 fpm (0-10.7 m/min) | Drum: 0-24 rpm | Fines Belt: 405 ft/min | Fines Belt: 405 ft/min
  • 62.9 gpm @ 2800 psi (238.1 L/min @ 172.4 bar [17240 kPa]) | Drum Operation: 0-42.6 gpm (161.3 L/min)
  • 4 independent hydraulic jacklegs | Fines Conveyor Frame: Part of trailer frame | Fines Conveyor Frame: 4 in x 8 in (10.2 cm x 20.3 cm) structural steel tubing
  • Hopper Opening: 13.2 ft x 5.3 ft (4 m x 1.6 m) | Apron Conveyor Rollers: 4 in (10.2 cm) diameter qty. 14 | Drum Diameter: 6 ft | Drum Support Description: 8 in (20.3 cm) diameter | Thrust Bearing Diameter: 5 in | Thrust Bearing Face: 2.9 in | Drum Angle Adjustability: 0-7 degrees | Brush Diameter: 14 in | Brush Assembly Support: Two 1.25-in (3.2-cm) sealed ball bearings | Head/Tail Pulley Type: Rubber-lagged, 12 in (30.5 cm ) diameter | Head Pulley Bearing: 2.4 in (6.1 cm) pillow block | Rubber Flashing: Adjustable, 0.25 in (6.44 cm) thick, 4 in (10.2 cm) | Tail Pulley Takeup: 12 in | Self-Cleaning Return Idlers: 6, each 4 in (10.2 cm) diameter | Head Pulley Type: Rubber lagged, 12 in (30.5 cm) diameter | Rubber Flashing: Adjustable, 0.25 in (0.64 cm) thick, 4 in (10.16 cm) | Self-Cleaning Tail Pulley: 10 in (25.4 cm) diameter, 2.4 in (6.1 cm) shaft | Tail Pulley Takeup: 12 in | Self-Cleaning Return Idlers: 11, each 4 in (10.2 cm) diameter | Conveyor Belt Type: 220 lb (99.8 kg), 2-ply, 2/16 in x 1/16 in (4.8 mm x 1.6 mm)
  • 54.5 ft
  • 113 in
  • 13.5 ft
  • Operation: 84.4 ft | Apron Conveyor: 16 ft | Drum: 26 ft | Fines Conveyor: 72.5 ft
  • Operation: 113 in | Apron Opening: 43 in | Drum Support Description: 4 in (10.2 cm) | Head/Tail Pulley Type: 38 in (99.65 cm) | Head Pulley Type: 38 in (99.65 cm) | Self-Cleaning Tail Pulley: 38 in (96.5 cm)
  • Operation: 15.9 ft | Apron Opening: 34 in | Hopper: 9.5 ft (2.9 m) from ground level at operating incline | Conveyor Belt Stacking: 16.6 ft (5.1 m) with drum at 4 deg
  • Bottom: 48 in
  • Apron Conveyor Belt: 48 in | 36 in
  • Tank: 200 gal
  • 6 cu yd
  • Approximately 200 cu yd (152.9 cu m) per hour with 0.5 in (1.3 cm) screens installed and material with moisture less than 40%
  • Drum Support Description: Four steel trunnion rollers | Drum Drive Chain: 140 WT | Maximum Screen Panels: 8 | Idler Type: 20 degrees CEMA "B" with permanently sealed bearings spaced at 24 in (20.96 cm) centers | Troughing Idler Type: 20 degrees CEMA "B" with permanently sealed bearings spaced at 24 in (60.96 cm) centers
  • 65000 lbs | Hitch: 30000 lbs
  • Bristle: Polyethylene