2024 Vermeer® Trommel Screens TR626 Tier 4F

Information

2024 Vermeer® Trommel Screens TR626 Tier 4F

With a 6 ft/1.83 m drum and a hopper that holds 6 cubic yards/4.6 cubic meters, the TR626 makes short work of processing material. Access the drum through removable side panels, drum end or top of the drum. Its 125 hp/93.2 kw John Deere 4045 Tier 4 Final is a powerful workhorse. Impressive 72.5 ft/22.1 m conveyor features self-cleaning tail pulley and return idlers.

Features may include:

Startup delay and alarm systems

Enhance worker safety with startup delay and alarm systems that notify your whole crew when the machine is about to start.

Tall, wide throat opening

Move material smoothly without bridging, thanks to a tall, wide throat opening.

Heavy-duty rollers

Extend belt life even under tough loading conditions with closely set, heavy-duty rollers supporting the apron conveyor.

Keep screen weights low

Keep screen weights low when processing wet materials by clamping on a smaller diameter tension screen wire and increasing screening area.

Reduced spillage

Speed up your clean up because the flashing and sheeting fit tightly against the drum and conveyors to reduce spillage.

Low hopper infeed height

Forget the loading ramps, since the 626 has a low hopper infeed height.

Photos

Highlights

  • Jasper, Georgia
  • 2024
  • Vermeer®
  • Trommel Screens TR626 Tier 4F
  • Model: PowerTech PVX 4.5L, 4045HFC93
  • Available
  • Operation: 113 in | Apron Opening: 43 in | Apron Conveyor Belt: 48 in | Head/Tail Pulley Type: 38" (996.5 cm) | Head Pulley Type: 38" (996.5 cm) | Self-Cleaning Tail Pulley Dimensions: 38" (96.5 cm)
  • Operation: 15.9 ft | Apron Opening: 34 in | Hopper: 9.5' (2.9 m) from ground level at operating incline | Conveyor Belt Stacking: 16.6' (5.1 m) with drum at 4 degrees | Conveyor Belt Stacking: 3' (.9 m) x 10' (3.1 m)

Specifications

  • 2024
  • Vermeer®
  • Trommel Screens
  • TR626 Tier 4F
  • General
  • Model: PowerTech PVX 4.5L, 4045HFC93
  • John Deere
  • Tier 4F
  • 4
  • Rating: 134 hp (93.2 kW) @ 2400 rpm, 398 ft-lb (531.6 Nm) of torque @ 1600 rpm
  • Spin-on
  • Dual element oversized
  • Drum: 48.8 cu in (800 cu cm) displacement | Conveyor: 38.4 cu-in | Conveyor Motor Displacement: 21.4 cu-in
  • Fuel Consumption: 3.5 gph (13.3 L/hr) under most operating conditions
  • Leaf spring
  • 235-75R 17.5H qty. 4
  • 950 cold cranking amps
  • System Voltage: 12 V, 120 amp alternator
  • Apron Conveyor: 0-35 fpm (0-10.7 m/min) | Drum: 0-24 rpm | Fines Belt: 405 ft/min | Fines Belt: 405 ft/min | Fines Belt: 705 ft/min | Maximum Variable Overs Belt: 290 ft/min
  • 62.9 gpm @ 2800 psi (238.1 L/min @ 172.4 bar [17240 kPa]) | Drum Operation: 0-42.6 gpm (161.3 L/min)
  • 4 independent hydraulic jacklegs | Fines Conveyor Frame: Part of trailer frame
  • Maximum Engine Operating Angle (Operating angles do not indicate safe machine operating angles): 30 deg | Hopper Opening: 13.2' x 5.3' (4 m x 1.6 m) | Apron Conveyor Rollers: 4" (10.2 cm) diameter | Drum Diameter: 6 ft | Drum Support Description: Four steel trunnion rollers 8 in (20.3 cm) diameter 4 in (10.2 cm) width | Thrust Bearing Diameter: 5 in | Thrust Bearing Face: 2.9 in | Drum Angle Adjustability: 0-7 degrees | Brush Diameter: 14 in | Head/Tail Pulley Type: Rubber-lagged, 12" (30.5 cm) diameter | Head Pulley Bearing: 2.5" (6.4 cm) pillow block | Rubber Flashing: Adjustable, .25" (6.44 cm) thick, 4" (10.2 cm) | Tail Pulley Takeup: 12 in | Self-Cleaning Return Idlers: 6, each 4" (10.2 cm) diameter | Head Pulley Type: Rubber lagged, 12" (30.5 cm) diameter | Self-Cleaning Tail Pulley Dimensions: 10" (25.4 cm) diameter, 2.4" (6.1 cm) shaft | Self-Cleaning Return Idlers: 11, each 4" (10.2 cm) diameter | Fines Conveyor Frame: 4" x 8" (10.2 cm x 20.3 cm) | Conveyor Belt Type: 150 lb (99.8 kg), 2 ply, 1/32" x 1/32" (.8 mm x 0.8 mm) | Fines Conveyor Frame: 2" x 8" (5.1 cm x 20.3 cm) structural steel building | Conveyor Belt Size: 48" (121.9 cm) wide with raised crescent | Conveyor Belt Type: 220 lb (99.8 kg), 2 ply, 2/16" x 1/16" (4.8 mm x 1.6 mm) | Self-Cleaning Tail Pulley Dimensions: 10" (25.4 cm) diameter, 51" (129.5 cm) wide with 2.4" (6.1 cm) shaft | Tail Pulley Takeup: 12 in | Solid Return Idler Size: 4" x 8" diameter | Overs Conveyor Frame: 4" x 8" (10.2 cm x 20.3 cm) structural steel tubing
  • 54.5 ft
  • 113 in
  • 13.5 ft
  • Operation: 84.4 ft | Apron Conveyor: 16 ft | Drum: 26 ft | Fines Conveyor: 72.5 ft | Fines Conveyor: 30.5 ft | Overs Conveyor: 19 ft
  • Operation: 113 in | Apron Opening: 43 in | Apron Conveyor Belt: 48 in | Head/Tail Pulley Type: 38" (996.5 cm) | Head Pulley Type: 38" (996.5 cm) | Self-Cleaning Tail Pulley Dimensions: 38" (96.5 cm)
  • Operation: 15.9 ft | Apron Opening: 34 in | Hopper: 9.5' (2.9 m) from ground level at operating incline | Conveyor Belt Stacking: 16.6' (5.1 m) with drum at 4 degrees | Conveyor Belt Stacking: 3' (.9 m) x 10' (3.1 m)
  • Bottom: 48 in
  • Belt: 36 in
  • 73 gal
  • Oil Volume with Filter: 15.5 qt
  • Tank: 200 gal
  • Approximately 200 cu yd (152.9 cu m) per hour with .5" (1.3 cm) screens installed and material with moisture less than 40%
  • Radiator Fan: Suction-type | Apron Conveyor Rollers: qty. 14 | Drum Drive Chain: 140 WT | Maximum Screen Panels: 8 | Brush Assembly Support: Two 1.25" (3.2 cm) sealed ball bearings | Idler Type: 20 degrees CEMA "B" with permanently sealed bearings spaced at 24" (60.96 cm) centers | Troughing Idler Type: 20 degrees CEMA "B" with permanently sealed bearings spaced at 24" (60.96 cm) centers | Head/Tail Pulley Type: Rubber lagged, crowned | Idler Type: 30 degrees CEMA "B" with permanently sealed bearings spaced at 41" (104 cm) centers
  • 6 cu yd
  • 65000 lbs | Hitch: 30000 lbs
  • Recommended: Mobil 15/40
  • Bristle: Polyethylene | Fines Conveyor Frame: structural steel tubing | Conveyor Belt Type: vulcanized | Head Pulley Type: Rubber lagged | Overs Conveyor Frame: structural steel tubing