2025 Vermeer® Trommel Screens TR5300

Information

2025 Vermeer® Trommel Screens TR5300

From either control, the operator can choose from four programmable presets or adjust machine settings based on incoming material.

Operators can control the machine through either the Vermeer DP10 display mounted on the control panel.

The TR5300 features a large, low feed height hopper that makes it easier to load with a loading ramp, making the trommel screen more mobile around the jobsite.

The hydraulic-driven chain drive system provides positive drum drive and allows the drum to lift off of the cog for service and maintenance.

From the dual-hinged doors on either side of the machine, you can perform machine maintenance efficiently through ease of access to components such as motor, trommel drum and drum drive.

Without having to change out the drum, you can adjust the screen panel quickly which will allow operators to change opening size, wire gauge and type of wire so you can separate a wide variety of material.

Features may include:

  • High productivity in a compact size
  • Minimize overall maintenance time
  • Complete control for overall jobsite confidence

Photos

Highlights

  • Jasper, Georgia
  • 2025
  • Vermeer®
  • Trommel Screens TR5300
  • Model: TD2.9L
  • Available
  • Operation: 112.8 in | Drum Support Description: 4" (10.2 cm) | Head Pulley Type: 38" (96.5 cm) wide | Self-Cleaning Tail Pulley Dimensions: 38" (96.5 cm)
  • Operation: 15 ft | Hopper: 9.5 | Conveyor Belt Stacking: 15'

Specifications

  • 2025
  • Vermeer®
  • Trommel Screens
  • TR5300
  • General
  • Model: TD2.9L
  • 4
  • Deutz
  • Spin-on
  • Dual element
  • Tier 4 Final/ Stage IV
  • Rating: 74 hp (55 kW) @ 2600 rpm and 181 ft-lb (245.4 Nm) of torque @ 1600 rpm
  • Conveyor Motor: 33 cu-in
  • Consumption: 4.6
  • Single Leaf Sprung
  • 445/50R22.5
  • 950 Cold Cranking Amp Group 31
  • System Voltage: 12
  • Drum: 0-24 RPM | Fines Belt: 500 ft/min
  • Drum Operation: 0-30.9 gpm (0-117.0 L/min) | Conveyor Operation: 17 gpm
  • Heavy Duty Structural Tubing | Fines Conveyor: 2" (5.1 cm) x 8" (20.3 cm) structural steel tubing
  • Maximum Engine Operating Angle (Operating angles do not indicate safe machine operating angles): 30 deg | Hopper Opening: 34x37 | Drum Diameter: 5 ft | Drum Support Description: Eight poly trunnion rollers 8" (20.3 cm) diameter | Thrust Bearing Diameter: 4 in | Thrust Bearing Face: 2.9 in | Drum Angle Adjustability: 0-7 degrees | Brush Diameter: 14 in | Brush Assembly Support: Two 1.25" (3.2 cm) sealed ball bearings | Head Pulley Type: 12" (30.5 cm) diameter | Head Pulley Bearing: 2 7/16" (6.2 cm) pillow block | Self-Cleaning Tail Pulley Dimensions: 10" (25.4 cm) diameter, 2.4" (6.1 cm) shaft | Head Pulley Takeup: 10 in | Self-Cleaning Return Idlers: 4" (10.2 cm) rubber disc
  • 36 in
  • 39 ft
  • 98.4 in
  • 13.4 ft
  • Bottom: 34 in
  • Operation: 89.9 ft | Drum: 15 ft | Fines Conveyor: 55 ft
  • Operation: 15 ft | Hopper: 9.5 | Conveyor Belt Stacking: 15'
  • Operation: 112.8 in | Drum Support Description: 4" (10.2 cm) | Head Pulley Type: 38" (96.5 cm) wide | Self-Cleaning Tail Pulley Dimensions: 38" (96.5 cm)
  • 44 gal
  • 5.5 cu yd
  • Tank: 55 gal
  • Radiator Fan: Suction | Drum Drive Chain: 140 custom extended pin | Maximum Screen Panels: 4 | Head Pulley Type: Rubber lagged | Troughing Idler Type: 20° CEMA "B" with permanently sealed bearings | Self-Cleaning Return Idlers: qty 8
  • Oil Volume with Filter: 8.4 qt
  • 100 cu yd (76.5 m3) per hr with .5" (12.7 mm) screens installed and material with moisture less than 40%
  • 32000 lbs | Hitch: 11600 lbs
  • Bristle: Polyethylene
  • Recommended: Mobil 15W40